New update

.gitignore

@@ -0,0 +1 @@
+site/

docs/install/bpq.md

@@ -1,48 +1,19 @@
 # BPQ
-## Raspberry Pi
-### Install Key
 
-**Do this once, only.**
+## Set Up Repo
 
-Our very own Hibby MM0RFN, also a Debian maintainer, has kindly packaged and is maintaining various Linux packet radio software, among them LinBPQ.
+If you have not already done so, set up the repo [as shown here](../repo.md).
 
-To start using his repo, you need tell your machine to trust the repo:
+## Install
 
-```
+To install LinBPQ from the repo, run the below commands:
-wget -q https://online-amateur-radio-club-m0ouk.github.io/oarc-packages/hibby.key
-sudo mv hibby.key /etc/apt/trusted.gpg.d/hibby.asc
-```
-
-### Set up Repo
-Then you need to add the repo for your OS:
-
-```
-# Ubuntu 22.04 LTS amd64
-sudo sh -c 'echo "deb https://online-amateur-radio-club-m0ouk.github.io/oarc-packages jammy main" >> /etc/apt/sources.list'
-
-# Raspberry Pi OS 12 - 'Bookworm'
-sudo sh -c 'echo "deb https://online-amateur-radio-club-m0ouk.github.io/oarc-packages bookworm main" >> /etc/apt/sources.list'
-
-# Raspberry Pi OS 11 - 'Bullseye'
-sudo sh -c 'echo "deb https://online-amateur-radio-club-m0ouk.github.io/oarc-packages bullseye main" >> /etc/apt/sources.list'
-
-# Debian 13 amd64
-sudo sh -c 'echo "deb https://online-amateur-radio-club-m0ouk.github.io/oarc-packages testing main" >> /etc/apt/sources.list'
-
-# Debian 12 amd64
-sudo sh -c 'echo "deb https://online-amateur-radio-club-m0ouk.github.io/oarc-packages bookworm main" >> /etc/apt/sources.list'
-```
-
-### Install
-
-After following the above steps, to install LinBPQ, run the below commands:
 
 ```
 sudo apt update
 sudo apt install linbpq
 ```
 
-### Configure
+## Configure
 
 ```
 sudo mv /usr/share/doc/linbpq/examples/bpq32.cfg /etc/bpq32.cfg

docs/install/linux.md

@@ -0,0 +1,68 @@
+# Linux Native Stack
+
+The linux native stack is highly configurable and can be easily installed on all Debian distros.
+
+## Install
+
+To get a basic node setup, the minimum viable software is:
+
+`apt install libax25 ax25-tools ax25-apps uronode`
+
+### BBS
+
+To set up a BBS install fbb
+
+`apt install fbb`
+
+## Basic Config
+
+We shall set up a single AX.25 port to receive calls and display Uronode to calling stations.
+
+### ax25 ports
+
+Set up your ax25 ports in `/etc/ax25/axports`
+
+The following example is for a NinoTNC:
+```
+# /etc/ax25/axports
+#
+# The format of this file is:
+#
+# name callsign speed paclen window description
+#
+uhf	UR0CAL-10	57600	255	2	UHF 9600bd
+```
+
+Modify the callsign to your own or your station's call.
+
+This has to be attached as to the modem, in effect telling the computer to
+listen to the modem's output. Run the below as root:
+
+`kissattach /dev/ttyACM0 uhf`
+
+### ax25d
+
+ax25d (ax25 daemon) listens to incoming data and directs calling stations to the application you want them to use.
+It can present different applications based on any combination of the callsign calling you, the callsign and SSID the calling station is calling and the port they are calling to.
+
+ax25d is controlled by `/etc/ax25/ax25d.conf`
+
+```
+# /etc/ax25/ax25d.conf
+#
+# ax25d Configuration File.
+#
+# AX.25 Ports begin with a '['.
+#
+[UR0CAL-10 via uhf]
+NOCALL   * * * * * *  L
+default  * * * * * *  - root  /usr/sbin/uronode uronode
+```
+
+Note the callsign, SSID and port are aligned with the axport in this example. Similar to axports, modify UR0CAL to our own callsign or your station's callsign.
+
+ax25d is started by running the below as root:
+
+`ax25d`
+
+Stations should be able to call uronode on your system using AX.25.

docs/radios/ft-7900.md

@@ -0,0 +1,22 @@
+# Yaesu FT-7900
+
+The FT-7900 is an 2m & 70cm radio manufactured by Yaesu from 2010 to the present day.
+
+## Bands
+
+| Band | Power | Modulation |
+| ---- | ----- | ---------- |
+| 2m | 0 - 50W | FM |
+| 70cm | 0 - 40W | FM |
+
+## Interface
+
+Yaesu Mini DIN
+
+## Settings
+
+## Known Examples
+
+| Location | Band | Modem | Mode |
+| -------- | ---- | ----- | ---- |
+| GB7HIB VHF Port | 2m | [NinoTNC](../modems/ninotnc.md) | 1200bd IL2P |

docs/radios/ft-891.md

@@ -0,0 +1,22 @@
+# Yaesu FT-891
+
+The FT-891 is an HF & 6m radio manufactured by Yaesu from 2016 to the present day.
+
+## Bands
+
+| Band | Power | Modulation |
+| ---- | ----- | ---------- |
+| HF | 0 - 100W | SSB |
+| 6m | 0 - 100W | SSB, FM |
+
+## Interface
+
+Yaesu Mini DIN
+
+## Settings
+
+## Known Examples
+
+| Location | Band | Modem | Mode |
+| -------- | ---- | ----- | ---- |
+| GB7HIB HF Port | 40m | [NinoTNC](../modems/ninotnc.md) | 300bd IL2P |

docs/radios/gm340.md

@@ -1,18 +1,20 @@
 # GM340
 
-The Motorola GM340 can be configured as VHF or UHF at the factory and supports deviation suitable for 1200bd and 9600bd
+The Motorola GM340 is a commercial radio. It can be configured as VHF or UHF at the factory and supports deviation suitable for 1200bd and 9600bd.
 
-## Prior Example
+## Bands
+
+| Band | Power | Modulation |
+| ---- | ----- | ---------- |
+| UHF | 25W | FM |
+
+## Interface
+
+## Settings
+
+
+## Known Example
 
 MM0RFN is using a GM340 as the 9600bd/UHF port on GB7HIB. 
 
 General programming advice from [BI7JTA](https://www.bi7jta.org/wiki/index.php?title=Main_Page#GM340.2FGM350.2FGM360) was followed, including connector definition. 
-
-## Power
-
-To change output power, open GM340 > Per Radio > RF with a double click and vary high/low power modes
-
-## RF Channel Properties
-
-To change frequency, open GM340 > per Channel > double click a channel and assign new frequency, spacing and power level (defined in Power section)
-

docs/radios/index.md

@@ -4,6 +4,20 @@ There are a huge number of radios we can use for packet radio, and they can be s
 
 ## Known good Beginner Radios
 
-| Radio |
+| Manufacturer | Radio | Band |
-| ----- |
+| ------------ | ----- | ---- |
-| [GM340](gm340.md) |
+| Motorola | [GM340](gm340.md) | UHF |
+| Yaesu | [FT-7900](ft-7900.md) | VHF / UHF |
+
+## VHF/UHF Radios
+
+| Manufacturer | Radio | Band |
+| ------------ | ----- | ---- |
+| Motorola | [GM340](gm340.md) | UHF |
+| Yaesu | [FT-7900](ft-7900.md) | VHF / UHF |
+
+## HF Radios
+
+| Manufacturer | Radio |
+| ------------ | ----- |
+| Yaesu | [FT-891](ft-891.md) |

docs/repo.md

@@ -0,0 +1,39 @@
+# Hibby's Repo
+## Install Signing Key
+
+First, you need tell your machine to trust the signature I verify the packages with:
+
+```
+wget -q https://online-amateur-radio-club-m0ouk.github.io/oarc-packages/hibby.key
+sudo mv hibby.key /etc/apt/trusted.gpg.d/hibby.asc
+```
+
+You can trust this key - it is contained in [Debian](https://salsa.debian.org/debian-keyring/keyring/-/blob/master/debian-keyring-gpg/0x03A1FB7A1904771B?ref_type=heads) and signed as trusted by other developers in the project.
+
+## Set up Repo
+Then you need to add the repo for your OS:
+
+```
+# Ubuntu 22.04 LTS amd64
+sudo sh -c 'echo "deb https://online-amateur-radio-club-m0ouk.github.io/oarc-packages jammy main" >> /etc/apt/sources.list'
+
+# Raspberry Pi OS 12 - 'Bookworm'
+sudo sh -c 'echo "deb https://online-amateur-radio-club-m0ouk.github.io/oarc-packages bookworm main" >> /etc/apt/sources.list'
+
+# Raspberry Pi OS 11 - 'Bullseye'
+sudo sh -c 'echo "deb https://online-amateur-radio-club-m0ouk.github.io/oarc-packages bullseye main" >> /etc/apt/sources.list'
+
+# Debian 13 amd64
+sudo sh -c 'echo "deb https://online-amateur-radio-club-m0ouk.github.io/oarc-packages testing main" >> /etc/apt/sources.list'
+
+# Debian 12 amd64
+sudo sh -c 'echo "deb https://online-amateur-radio-club-m0ouk.github.io/oarc-packages bookworm main" >> /etc/apt/sources.list'
+```
+
+## Update
+
+Once the repo is setup, refresh your package lists and we're good to go:
+
+```
+sudo apt update
+```

mkdocs.yml

@@ -3,6 +3,7 @@ site_url: https://packetradio.debian.net
 nav:
   - Home: "index.md"
   - About: "about.md"
+  - Glossary: "glossary.md"
   - Radios: 
     - "radios/index.md"
   - Modems:
@@ -14,7 +15,14 @@ nav:
   - Software Setup:
     - "software.md"
     - BPQ: "install/bpq.md"
+    - Linux: "install/linux.md"
   - Node Configuration:
     - BPQ: "config/bpq.md"
-  - Glossary: "glossary.md"
+  - Misc:
-theme: readthedocs
+    - Repo Setup: "repo.md"
+theme: 
+  name: readthedocs
+  navigation_depth: 5
+  collapse_navigation: False 
+  sticky_navigation: False
+  highlightjs: True