97 lines
3.4 KiB
Markdown
97 lines
3.4 KiB
Markdown
# BPQ
|
|
|
|
## Set Up Repo
|
|
|
|
If you have not already done so, set up the repo [as shown here](../repo.md).
|
|
|
|
## Install
|
|
|
|
To install LinBPQ from the repo, run the below commands:
|
|
|
|
```
|
|
sudo apt update
|
|
sudo apt install linbpq
|
|
```
|
|
|
|
## Pre-Configure
|
|
|
|
```
|
|
sudo cp /usr/share/doc/linbpq/examples/bpq32.cfg /etc/bpq32.cfg
|
|
sudo nano /etc/bpq32.cfg
|
|
sudo chown :linbpq /etc/bpq32.cfg
|
|
sudo chmod 644 /etc/bpq32.cfg
|
|
```
|
|
!!! note
|
|
|
|
Without a config file installed to `/etc/bpq32.cfg`, BPQ from the repo will not start. If you are looking to use a config file in a different location, remove or modify `ConditionPathExists=/etc/bpq32.cfg` in `/usr/lib/systemd/system/linbpq.service`
|
|
|
|
## Configure
|
|
|
|
The configuration file I ship in the repo, there are hopefully some obvious fields to fill out. Once all the below holes are filled, you should be able to log in either with [QtTermTCP](../clients/qtttcp.md) or in your web browser at [localhost:8008](http://127.0.0.1:8008)), assuming you're on the same computer as the node.
|
|
|
|
| Field | Example | Purpose
|
|
| ----- | ------- | -------
|
|
| NODECALL | MM0RFN | The callsign your node shall identify as
|
|
| NODEALIAS | RFNNOD | The alias a calling NET/ROM station can use to connect directly to you
|
|
| LOCATOR | IO87dc | A 6 figure Maidenhead square where you are
|
|
| PASSWORD | test123 | A sysop password for configuration activities
|
|
| AUTOSAVE | 1 | Autosave the NET/ROM Nodes Table on shutdown
|
|
| NODESINTERVAL | 30 | Interval between NET/ROM NODES broadcasts in minutes
|
|
| MINQUAL | 50 | The minimum quality of NET/ROM node included in your NODES broadcasts.
|
|
| CTEXT | `Hi you look great! ***` | Text displayed when a user connects
|
|
|
|
### Ports
|
|
|
|
Port configuration blocks in BPQNode aren't too complicated. A common Gotcha is that you configure a port specific broadcast and end up double-broadcasting, both the node master broadcast and the port specific one.
|
|
|
|
#### KISS
|
|
|
|
A common port entry for a [NinoTNC](../modems/ninotnc.md) specifically (but also, more generally, a KISS Modem) looks like:
|
|
|
|
```
|
|
PORT
|
|
PORTNUM=1
|
|
ID=VHF
|
|
TYPE=ASYNC
|
|
PROTOCOL=KISS
|
|
KISSOPTIONS=ACKMODE
|
|
COMPORT=/dev/ttyACM0
|
|
SPEED=57600
|
|
FRACK=4000
|
|
PACLEN=150
|
|
DIGIFLAG=0
|
|
QUALITY=192
|
|
MINQUAL=20
|
|
ENDPORT
|
|
```
|
|
|
|
Key settings to observe are the `COMPORT`, which should be the serial port of the device, and `SPEED`. For a NinoTNC this is always 57600, but for QtSoundModem, Direwolf or older hardware may be 9600 or something else. Check your modem configuration!
|
|
|
|
`QUALITY` sets the assumed quality of connections coming in - I recommend higher quality (up to 200) for higher speed links. Setting this to 0 will disable NET/ROM on the port, and this is current recommended standard practise on HF within the UK Packet Radio Network.
|
|
|
|
#### Telnet
|
|
|
|
BPQ's Telnet Port sets the TCP Ports for Telnet, FBB and HTTP connections, alongside the username and password. This will come in useful when using [QtTTCP](../clients/qtttcp.md) as a monitor and control application.
|
|
|
|
```
|
|
PORT
|
|
PORTNUM=9
|
|
ID=Telnet
|
|
DRIVER=Telnet
|
|
CONFIG
|
|
LOGGING=1
|
|
CMS=1
|
|
DisconnectOnClose=1
|
|
TCPPORT=8010
|
|
FBBPORT=8011
|
|
HTTPPORT=8008
|
|
LOGINPROMPT=user:
|
|
PASSWORDPROMPT=password:
|
|
MAXSESSIONS=10
|
|
CTEXT=Thanks for connecting\n Enter ? for list of commands\n\n
|
|
USER=username,xxxxxxxx,m0aaa,,SYSOP
|
|
ENDPORT
|
|
```
|
|
|
|
`USER` is the key configuration to change here - change `username` to your desired administrator username, `xxxxxxx` to the password and `m0aaa` to the callsign of the administrator.
|